Delivery program

Product range	Contactors
Application	Mains contactors for resistive loads from 1000 A
Subrange	AC -1 contactors greater than 1000 A
Utilization category	AC-1: Non-inductive or slightly inductive loads, resistance furnaces
Connection technique	Screw connection
Rated operational current
AC-1Conventional free air thermal current, 3 pole, 50 - 60 HzOpenat 40 °C [Ith =Ie]	2700 A
AC-1Conventional free air thermal current, 1 poleopen [Ith ]	5500 A
Contact sequence
For use with	DILM820-XHI…
Actuating voltage	RAW 250: 230 - 250 V 50 - 60 Hz/230 - 350 V DC
Voltage AC/DC	AC and DC operation
Auxiliary contacts
possible variants at auxiliary contact module fitting options	on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA
Side mounting auxiliary contacts
Instructions	integrated suppressor circuit in actuating electronics660 V, 690 V or 1000 V: not directly reversing
Note concerning the product	Classic DILM1600, DILH2000, DILH2200 A1/A2 werden wie bisher gewohnt an Spannung gelegt Direct from the PLC An die Anschlüsse A3/A4 kann direkt ein 24-V-Ausgang der SPS angeschlossen werden. From a low-power actuating device Gering belastbare Befehlsgeber wie Leiterplattenrelais, Befehlsgeräte oder Positionsschalter können direkt an A10/A11 angeschlossen werden. ① Stopping in the event of an emergency (emergency switching off)② max. Cable capacitance 6 nF

Technical data

General
Standards	IEC/EN 60947, VDE 0660, UL, CSA, CCC
Lifespan, mechanicalAC operated [Operations]	5 x 106
Lifespan, mechanicalDC operated [Operations]	5 x 106
Operating frequency, mechanicalAC operated [Operations/h]	1000
Operating frequency, mechanicalDC operated [Operations/h]	1000
Climatic proofing	Damp heat, constant, to IEC 60068-2-78Damp heat, cyclic, to IEC 60068-2-30
Ambient temperatureOpen	-40 - +60 °C
Ambient temperatureStorage	- 40 - + 80 °C
Mounting position
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msMain contactsN/O contact	10 g
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msAuxiliary contactsN/O contact	10 g
Mechanical shock resistance (IEC/EN 60068-2-27)Half-sinusoidal shock, 10 msAuxiliary contactsN/C contact	8 g
Degree of Protection	IP00
Weight	32 kg
Terminal capacity main cableBusbar [Width]	100 mm
Main cable connection screw/bolt	M12
Tightening torque	1.2 Nm
Terminal capacity control circuit cablesSolid	1 x (0.75 - 2.5)2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cablesFlexible with ferrule	1 x (0.75 - 2.5)2 x (0.75 - 2.5) mm2
Terminal capacity control circuit cablesSolid or stranded	18 - 14 AWG
Stripping length	10 mm
Control circuit cable connection screw/bolt	M3.5
ToolMain cableWidth across flats	18 mm
ToolControl circuit cablesPozidriv screwdriver	2 Size
ToolControl circuit cablesStandard screwdriver	0.8 x 5.5/1 x 6 mm
Main conducting paths
Rated impulse withstand voltage [Uimp]	8000 V AC
Overvoltage category/pollution degree	III/3
Rated insulation voltage [Ui]	1000 V AC
Rated operational voltage [Ue]	1000 V AC
Safe isolation to EN 61140between coil and contacts	500 V AC
Safe isolation to EN 61140between the contacts	500 V AC
Making capacity (p.f. to IEC/EN 60947)	9840 A
Breaking capacity 220 V 230 V	8200 A
Breaking capacity 380 V 400 V	8200 A
Breaking capacity 500 V	8200 A
Breaking capacity 660 V 690 V	8200 A
Breaking capacity 1000 V	5800 A
Component lifespan	AC1: See → Engineering, characteristic curves
AC
AC-1Rated operational currentConventional free air thermal current, 3 pole, 50 - 60 HzOpenat 40 °C [Ith =Ie]	2700 A
AC-1Rated operational currentConventional free air thermal current, 3 pole, 50 - 60 HzOpenat 50 °C [Ith =Ie]	2400 A
AC-1Rated operational currentConventional free air thermal current, 3 pole, 50 - 60 HzOpenat 55 °C [Ith =Ie]	2300 A
AC-1Rated operational currentConventional free air thermal current, 3 pole, 50 - 60 HzOpenat 60 °C [Ith =Ie]	2200 A
AC-1Rated operational currentConventional free air thermal current, 1 poleNote	at maximum permissible ambient air temperature
AC-1Rated operational currentConventional free air thermal current, 1 poleopen [Ith ]	5500 A
Current heat loss
3 pole, at Ith (60°)	231 W
Magnet systems
Voltage toleranceUS	230 - 250 V 50/60 Hz230 - 350 V DC
Voltage toleranceAC operated [Pick-up]	0.7 x US min - 1.15 x US max x US
Voltage toleranceDC operated [Pick-up]	0.7 x US min - 1.15 x US max x US
Voltage toleranceAC operated [Drop-out]	0.2 x US max - 0.6 x US min x US
Voltage toleranceDC operated [Drop-out]	0.2 x US max - 0.6 x US min x US
Power consumption of the coil in a cold state and 1.0 x USNote on power consumption	Control transformer with uk ≦ 7%
Power consumption of the coil in a cold state and 1.0 x USPull-in power [Pick-up]	1400 W
Power consumption of the coil in a cold state and 1.0 x USSealing power [Sealing]	17.3 W
Duty factor	100 % DF
Changeover time at 100 % US (recommended value)Main contactsClosing delay	70 ms
Changeover time at 100 % US (recommended value)Main contactsOpening delay	40 ms
Behaviour in marginal and transitional conditionsSealingVoltage interruptions(0 … 0.2 x Uc min) ≦ 10 ms	Time is bridged successfully
Behaviour in marginal and transitional conditionsSealingVoltage interruptions(0 … 0.2 x Uc min) > 10 ms	Drop-out of the contactor
Behaviour in marginal and transitional conditionsSealingVoltage drops(0.2 … 0.6 x Uc min) ≦ 12 ms	Time is bridged successfully
Behaviour in marginal and transitional conditionsSealingVoltage drops(0.2 … 0.6 x Uc min) > 12 ms	Drop-out of the contactor
Behaviour in marginal and transitional conditionsSealingVoltage drops(0.6 … 0.7 x Uc min)	Contactor remains switched on
Behaviour in marginal and transitional conditionsSealingExcess voltage(1.15 … 1.3 x Uc max)	Contactor remains switched on
Behaviour in marginal and transitional conditionsSealingPick-up phase(0 … 0.7 x Uc min)	Contactor does not switch on
Behaviour in marginal and transitional conditionsSealingPick-up phase(0.7 x Uc min … 1.15 x Uc max)	Contactor switches on with certainty
Admissible transitional contact resistance (of the external control circuit device when actuating A11)	≦ 500 mΩ
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2)High	15 V
PLC signal level (A3 - A4) to IEC/EN 61131-2 (type 2)Low	5 V
Electromagnetic compatibility (EMC)
Electromagnetic compatibility	This product is designed for operation in industrial environments (environment A). Its use in residential environments (environment B) may cause radio-frequency interference, requiring additional noise suppression measures.
Rating data for approved types
Switching capacityGeneral use	2200 A
Auxiliary contactsPilot DutyAC operated	A600
Auxiliary contactsPilot DutyDC operated	P300
Auxiliary contactsGeneral UseAC	15 A
Auxiliary contactsGeneral UseDC	1 A
Special Purpose RatingsResistance Air Heating480V 60Hz 3phase, 277V 60Hz 1phase	2200 A
Special Purpose RatingsResistance Air Heating600V 60Hz 3phase, 347V 60Hz 1phase	2200 A

Design verification as per IEC/EN 61439

Technical data for design verification
Rated operational current for specified heat dissipation [In]	2200 A
Heat dissipation per pole, current-dependent [Pvid]	77 W
Equipment heat dissipation, current-dependent [Pvid]	0 W
Static heat dissipation, non-current-dependent [Pvs]	13 W
Heat dissipation capacity [Pdiss]	0 W
Operating ambient temperature min.	-40 °C
Operating ambient temperature max.	+60 °C
IEC/EN 61439 design verification
10.2 Strength of materials and parts10.2.2 Corrosion resistance	Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.1 Verification of thermal stability of enclosures	Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.2 Verification of resistance of insulating materials to normal heat	Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.3.3 Verification of resistance of insulating materials to abnormal heat and fire due to internal electric effects	Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.4 Resistance to ultra-violet (UV) radiation	Meets the product standard's requirements.
10.2 Strength of materials and parts10.2.5 Lifting	Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts10.2.6 Mechanical impact	Does not apply, since the entire switchgear needs to be evaluated.
10.2 Strength of materials and parts10.2.7 Inscriptions	Meets the product standard's requirements.
10.3 Degree of protection of ASSEMBLIES	Does not apply, since the entire switchgear needs to be evaluated.
10.4 Clearances and creepage distances	Meets the product standard's requirements.
10.5 Protection against electric shock	Does not apply, since the entire switchgear needs to be evaluated.
10.6 Incorporation of switching devices and components	Does not apply, since the entire switchgear needs to be evaluated.
10.7 Internal electrical circuits and connections	Is the panel builder's responsibility.
10.8 Connections for external conductors	Is the panel builder's responsibility.
10.9 Insulation properties10.9.2 Power-frequency electric strength	Is the panel builder's responsibility.
10.9 Insulation properties10.9.3 Impulse withstand voltage	Is the panel builder's responsibility.
10.9 Insulation properties10.9.4 Testing of enclosures made of insulating material	Is the panel builder's responsibility.
10.10 Temperature rise	The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
10.11 Short-circuit rating	Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.12 Electromagnetic compatibility	Is the panel builder's responsibility. The specifications for the switchgear must be observed.
10.13 Mechanical function	The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.

Technical data ETIM 7.0

Low-voltage industrial components (EG000017) / Power contactor, AC switching (EC000066)
Electric engineering, automation, process control engineering / Low-voltage switch technology / Contactor (LV) / Power contactor, AC switching (ecl@ss10.0.1-27-37-10-03 [AAB718015])
Rated control supply voltage Us at AC 50HZ	230 - 250 V
Rated control supply voltage Us at AC 60HZ	230 - 250 V
Rated control supply voltage Us at DC	230 - 250 V
Voltage type for actuating	AC/DC
Rated operation current Ie at AC-1, 400 V	2700 A
Rated operation current Ie at AC-3, 400 V	0 A
Rated operation power at AC-3, 400 V	0 kW
Rated operation current Ie at AC-4, 400 V	0 A
Rated operation power at AC-4, 400 V	0 kW
Rated operation power NEMA	0 kW
Modular version	No
Number of auxiliary contacts as normally open contact	2
Number of auxiliary contacts as normally closed contact	2
Type of electrical connection of main circuit	Rail connection
Number of normally closed contacts as main contact	0
Number of main contacts as normally open contact	3

Approvals

Product Standards	IEC/EN 60947-4-1; UL 60947-4-1; CSA - C22.2 No. 60947-4-1-14; CE marking
UL File No.	E29096
UL Category Control No.	NLDX
CSA File No.	012528
CSA Class No.	3211-04
North America Certification	UL listed, CSA certified
Specially designed for North America	No

Characteristics

Side mounting auxiliary contacts
possible variants at auxiliary contact module fitting options	on the side: 2 x DILM820-XHI11(V)-SI; 2 x DILM820-XHI11-SA
Characteristic curve
	Short-time loading, 3-poleTime interval between two loading cycles: 15 minutes

Dimensions

DILM1600DILH2000, DILH2200

DILH2200/22(RAW250), Контактор EATON, арт. 111793